Home

Scout Bracelet

  • Color_wrapped_bangle-31 Pin-it%402x

Details

Color, texture and sparkle - just a few of our favorite things, and this bracelet has them all! Craft this DIY bracelet to add to add a little color to your stack and warm up your winter.

Tools

Materials

  • fabric wrapped cord
  • embroidery thread
  • rhinestone chain
  • glue
  • gold end caps
  • jump rings
  • headpins
  • lobster clasp

Time

20 minutes + drying time
Color-wrapped-bangle-2 Pin-it%402x

Gather your tools and materials.

Color-wrapped-bangle-3 Pin-it%402x

Wrap the fabric cord around your wrist and mark where the cord meets.

Color-wrapped-bangle-4 Pin-it%402x

If you like your bracelets on the tighter side cut about 5-10mm back from this point. If you like your bracelets on the looser side cut right where you marked. Remember that when the bracelet is completed we are going to be adding a little length from the lobster clasp and jump rings.

Color-wrapped-bangle-5 Pin-it%402x

Unwind a bit of thread from the card and tie a knot around one end of cord (leaving a 2" tail of thread - we will use this later). We want the knot to eventually be hidden by the end caps. To make sure tthis happens and your knot is in the right place, hold the end cap up to the cord.

Color-wrapped-bangle-6 Pin-it%402x

With the long piece of thread start wrapping it around the fabric cord at a diagonal. You should have a wrap about every 5 mm or so. It's really up to you how much thread you want to see here.

Color-wrapped-bangle-7 Pin-it%402x

Grab the rhinestone chain - you want this centered on the bracelet. Line it up in the center of the fabric cord and attach it by going around in the diagonal with the thread. You should go in between every single stone.

Color-wrapped-bangle-10 Pin-it%402x

Wrap the entire rhinestone chain to the bracelet and finish going all the way down the fabric cord. Tie a knot in the same place as we did on the opposite side.

Color-wrapped-bangle-11 Pin-it%402x

Then go back down the length of the bracelet in the opposite direction, creating a cross pattern over the thread you already wrapped.

Color-wrapped-bangle-15 Pin-it%402x

Go in between every single rhinestone again and all the way down to your starting point. Tie a knot right above the first one and then tie the end of thread to the initial 2" of thread we left at the beginning.

Color-wrapped-bangle-16 Pin-it%402x

Snip off the excess cord, leaving a small tail that we will tuck into the end cap.

Color-wrapped-bangle-17 Pin-it%402x

Place on headpin into the hole of an end cap. The round head on the headpin should be on the inside of the cap.

Color-wrapped-bangle-18 Pin-it%402x

Add a dab of glue to the inside of the cap.

Color-wrapped-bangle-19 Pin-it%402x

Push the fabric cord and the thread into the cap. Twisting it a little as you insert the cord will help distribute the glue. If any glue comes out the hole in the top just wipe it clean with a paper towel.

Color-wrapped-bangle-21 Pin-it%402x

Repeat on the opposite side. Let this sit to dry for at least 6 hours before moving on to the next step.

Color-wrapped-bangle-25 Pin-it%402x

Create a small loop at the base of the end cap using your round nose pliers. Get the 411 on mastering those loops here.

Color-wrapped-bangle-25 Pin-it%402x

To make this loop a little stronger, wrap the end of the wire once, around the bottom of the loop.

Color-wrapped-bangle-26 Pin-it%402x

Snip off the excess wire with your clippers. Make the same loop on the other side of the bracelet.

Color-wrapped-bangle-27 Pin-it%402x

TO finish the bracelet we are going to add 2 jump rings to one side and 2 jump rings + a lobster clasp to the other side. You can add or subtract jump rings here to fit your wrist better.

Color-wrapped-bangle-29 Pin-it%402x

Open the jump rings with the help of your chain nose pliers and attach the components together.

Color-wrapped-bangle-30 Pin-it%402x

All done!!!